Best Coaxial Stripping Machine Supplier in China

Semi-automatic Coaxial Stripping Machine Description of technical parameters

Device name: 8015

Processing cable type: coaxial cable, triaxial cable, shielded cable, rigid cable

Maximum processing cable diameter: 80.00mm

Cutting depth unit: 0.01mm

Maximum stripping length: 80mm

Maximum number of stripping layers: 9 layers

Drive method: motor, rolling screw drive (imported from Japan)

Display mode: touch interface

Blade: 4 pieces, material: imported Swiss tungsten steel

Centering sheet: 4 pieces, material: Japan SKD11

Clamping device: motor driven, clamping force program control

Productivity: 300-800 pcs/h (depending on cable type)

Opening mode: push button switch, foot switch

Power supply: 220V 50/60Hz Power: 250W

Weight: 30KG

Overall size: 650X220X350mm

Working environment: 0-45 degrees, moderate dryness, non-vibration work surface, moderate dryness workshop

Home description

1. Total: Set by the total production volume per batch. (range 0-65535).
2. Quantity: Current count in the production process (0-65535).
3. Output to zero: Clear the numerical numerical of the current quantity.
4. Emergency stop: When this button is pressed, the machine enters the emergency stop state and all motors stop rotating.
5. Serial number: The file number pre-stored of the cable, which can save 50 kinds of different specifications of the cable program, and automatically read the data stored of the current serial number after entering the serial number.
6. Linkage delay: Automatically start and run the machine according to the delay setting and turn off the function when it is set to 0.
7. Number of layers: Set according to the number of layers required for current cable processing.
8. Start: Press to start the machine after normal operation, if the machine is not reset state will start the reset process
9. Stop: When the machine is in automatic cyclic start mode, after pressing “stop”, the machine will stop cyclic operation after the current program is executed.
10. Reset: After pressing the “reset”, the machine begins to find the origin for self-reset, and the machine can be used normally after the reset is completed, and the machine must be reset after changing the stripping length, serial number, number of layers and manual control.
11. Parameter interface: Press the “parameter interface” to jump to the parameter setting interface.
12. Manual interface: Pressing the “manual interface” will jump to the manual operation interface.
13. IO interface: When this button is pressed, it will jump to the IO monitoring interface.
14. Normal mode half-stripping valid: The machine will run all actions according to the set numerical, and the cable jacket can be half-stripped.
15. Speed mode half-stripping invalid: The machine will omit part of the numerical in speed operation, directly cut each layer and strip at the same time, this mode cannot be half-stripping.

Parameter interface description

1. Current program serial number: The currently used stored program serial number (0-49).
2. Stripping delay: Since the speed of the rotating motor is too fast, there will be scratches caused by stripping before stopping, so it is necessary to set a delay to perform the stripping action after the rotating motor stops.
3. Retracting speed: The speed at which the blade opens when the machine is running.
4. Forward and Retracting speed: The speed at which the machine is moving forward.
5. Clamping speed: The travel speed of clamping and loosening of the clamping mechanism.
6. Limit Retracting distance: The more distance traveled when stripping in speed mode.
7. Clamping cable diameter distance: The distance at which the clamp is closed when the machine is running.
8. Gripper standby distance: The distance of the clamp in standby after the machine is reset and after the operation is completed.
9. Blade opening distance: The distance that the blade is open when the machine starts to move forward, if you enter small number will cause the blade will be damaged the cable.
10. Blade closing delay: After the last layer of stripping action is completed, the blade is delayed returning to the closed state, so as to prevent individual wires from being taken out and jammed on the blade due to the blade edge closing too quickly.
11. Copy program: When you press this button, select the serial number to be copied to on the program interface, and press the “copy program” button after the selection is completed, then the program copy is complete.
12. Home: Jump to the main interface.
13. Save: Save the data set on the parameters page to the current program serial number.
14. Next: Jump to the Layer 1 setting page.

Layer 1 setting description

1. Length of stripping: Length of stripping of the current number of layers (range 0.00-80.00mm).
2. Half-stripping: The half-stripping numerical is greater than the Length of stripping numerical = full stripping without leaving jacket is suitable for finished product processing, and the half-stripping numerical is less than the Length of stripping numerical= half stripping jacket on the wire, suitable for semi-finished product processing.
3. Cutting time: It takes residence time to process the first layer of cutting diameter rotary blade. (range 0.01-5ms) When this parameter is zero, the cutting effect is not good.
4. Blade closing speed: The speed when the blade of the current layer is closed, and the speed is appropriately reduced when the jacket is soft.
5. Stripping speed: The speed of stripping of the current layer, and the speed is appropriately reduced when the jacket and the core wire are bonded tightly.
6. Rotation speed: The rotation speed of the current layer rotation motor.
7. Distance of blade: Setting the distance (size) of the blade edge of the current layers, the smaller the core wire, the smaller the blade distance, if there is a cut, the distance need to be appropriately increased.
8. Retract blade: After cutting, stripping after the blade edge is opened to avoid scratches, and increase the retract numerical appropriately if there is a scratch.
9. Shaking cycle: In the absence of air stream, the shaking function can be used to prevent the jacket from remaining at the blade edge and affecting the subsequent wire.
10. Blow time: When an air stream is connected, the blowing time can be set to blow away the jacket remaining at the blade edge.
11. Spin stripping: When the “spin stripping” button shows (No), the rotary blade will stop and then Strip again.

When the “spin stripping” button shows (Yes), the blade holder will continue to rotate and strip at the same time, and the stripped cable is twisted well.

12. Rotation direction: When the direction button shows (obverse), the rotating blade rotates clockwise. When the direction button displays (reverse), the rotary blade rotates against the clock.
13. Main page: Jump to the main interface.
14. Up: When you press this button, you will be taken to the parameter setting interface.
15. Next: When you press this button, you will be taken to the second main interface.
16. The subsequent layer number setting is the same as this layer setting method.

Manual interface

• 1. 1. Enter blade:

When the button is pressed, the blade edge motor will continue to feed and close the blade edge according to the manual speed.

• 1.2. Retracting blade:

When the button is pressed, the blade edge motor will continue to retract and open the blade edge according to the manual speed.

• 1.3. Return home:

When the button is pressed, the blade edge motor will automatically return to start then stop and light up the return-home indication.

• 1.4. Current position:

Display the position of the current motor.

• 1.5. Confirm:

After clicking the current numerical box, enter the numerical and press to confirm, the motor will run to the numerical position.

• 2.1. Forward:

When the button is pressed, the forward motor continues to advance at the manual speed.

• 2.2. Back:

When the button is pressed, the forward motor will continue to rewind according to the manual speed.

• 2.3. Return home:

When the button is pressed, the blade edge motor will automatically return to start then stop and light up the return-home indication

• 2.4. Current position:

Displays the position of the current motor.

• 2.5. Confirm:

After clicking the current stroke numerical box, enter the numerical and press to confirm, the motor will run to the numerical position.

• 3.1. Clamping:

When the button is pressed, the clamping motor will continue to clamp according to the manual speed.

• 3.2. Loose:

When the button is pressed, the clamping motor will continue to loosen according to the manual speed.

• 3.3. Return home:

When the button is pressed, the clamping motor will automatically return to the origin and stop and light up the return-home indication.

• 3.4. Current stroke:

Display the position of the current motor.

• 3.5. Confirm:

After clicking the current numerical box, enter the numerical and press to confirm, the motor will run to the numerical position.

• 4.1. Forward moving:

When pressing the button, the blade holder will continue to rotate clockwise according to the manual speed.

• 4.2. Reversal Moving:

When pressing the button, the blade holder will continue to rotate counterclockwise according to the manual speed.

• 4.3. Blow air:

When the button is pressed, the machine blows. (6010 Exclusive Feature)

• 5.1. Home:

Press this button to jump to the Home.

• 5.2. Parameter interface:

Jump to the parameter setting page.

• 5.3. IO interface:

Jump to the IO monitoring page.

Stripping settings: figure

Machine configuration checklist

If you are interested in the product, please contact us